The TI TMP75/TMP175 and the NXP LM75B share the TMP105 register map and
control semantics, differing only in a few details. Model them as
variants of the TMP105, parameterised by a small per-type class
descriptor covering the fault-queue depths, the writable config bits,
the converter resolution, the set-point masks and the TMP75's
alert-clear on thermostat-mode change.
The variant is class data, not migrated state, so the wire format is
unchanged and all variants share the existing vmstate.
While here, align the shared shutdown handling with the hardware:
entering shutdown now clears the ALERT/OS output in interrupt mode,
correcting the base TMP105 as well.
Signed-off-by: Emmanuel Blot <emmanuel.blot@free.fr>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/qemu-devel/20260731-sanmiguel-bmc-locator-v2-7-1266926ba769@free.fr
Signed-off-by: Cédric Le Goater <clg@redhat.com>
The fault-queue depth selected in the configuration register was decoded
but never consulted, so the ALERT pin tripped on the very first
out-of-limit conversion regardless of the programmed depth.
Track the consecutive-fault count and only change the ALERT state once
it reaches the programmed depth; any in-range conversion clears the
count. The default configuration keeps the previous behaviour. The count
is migrated through an optional subsection so existing streams stay
compatible.
Signed-off-by: Emmanuel Blot <emmanuel.blot@free.fr>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/qemu-devel/20260731-sanmiguel-bmc-locator-v2-4-1266926ba769@free.fr
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Previously the device reset routine was invoked once from realize() and
never registered with the reset subsystem, so a system or bus reset left
the TMP105 registers untouched. Convert tmp105_reset() into a proper
Resettable hold phase (tmp105_reset_hold) registered through
ResettableClass::phases.hold, and drop the manual call from realize() as
the reset framework now drives it. This matches the scheme used by the
other hw/sensor I2C devices.
Signed-off-by: Emmanuel Blot <emmanuel.blot@free.fr>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/qemu-devel/20260731-sanmiguel-bmc-locator-v2-3-1266926ba769@free.fr
Signed-off-by: Cédric Le Goater <clg@redhat.com>
The TMP105State struct, its cast macro and typedef are used only within
tmp105.c. Move them out of the public header into the source file and
drop the now-unused includes; the header is reduced to the TYPE_TMP105
name, with its guard renamed to the path-derived form per current QEMU
convention.
While here, normalize the source file include order to match the other
hw/sensor devices.
Signed-off-by: Emmanuel Blot <emmanuel.blot@free.fr>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/qemu-devel/20260731-sanmiguel-bmc-locator-v2-1-1266926ba769@free.fr
Signed-off-by: Cédric Le Goater <clg@redhat.com>
The ADC128D818 is a TI 12-bit, 8-channel I2C ADC used on several
OpenBMC platforms for voltage and temperature monitoring.
Implement the device with:
- four operating modes
- 12-bit voltage conversion from QOM inputs
- 9-bit temperature conversion from milli-degree Celsius QOM inputs
- switchable internal or external voltage reference
- per-channel high/low limit registers
- interrupt support
- software reset
- one-shot conversion support in shutdown mode
Reviewed-by: Alexander Hansen <alexander.hansen@9elements.com>
Tested-by: Alexander Hansen <alexander.hansen@9elements.com>
Signed-off-by: Emmanuel Blot <emmanuel.blot@free.fr>
Link: https://lore.kernel.org/qemu-devel/20260707091609.97759-2-emmanuel.blot@free.fr
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Use error_setg_errno() instead of passing the value of strerror() or
g_strerror() to error_setg().
The separator between the error message proper and the value of
strerror() changes from " : ", "", " - ", "- " to ": " in places.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20251121121438.1249498-14-armbru@redhat.com>
Acked-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
printf() unconditionally prints to the console which disturbs `-serial stdio`.
Fix that by converting into a trace event. While at it, add some tracing for
read and write access.
Fixes: 7e7c5e4c1b "Nokia N800 machine support (ARM)."
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20241103143330.123596-5-shentey@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Per datasheet, "HIGH AND LOW LIMIT REGISTERS", the lower 4 bit
of the limit registers are unused and always report 0.
The lower 4 bit should not be used for temperature comparisons,
so mask the unused bits before storing the limits.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20240906154911.86803-6-philmd@linaro.org>
[PMD: Update tests/qtest/ files]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Per datasheet, "ONE-SHOT (OS)", the OS bit always returns 0 when reading
the configuration register.
Clear the ONE_SHOT bit in the WRITE path. Now than the READ path is
simpler, we can also simplify tmp105_alarm_update().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20240906154911.86803-5-philmd@linaro.org>
The next commit will clear the ONE_SHOT bit in the WRITE
path (to keep the READ path trivial). As a preliminary step,
pass the 'oneshot' value as argument to tmp105_alarm_update().
No logical change intended.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <20240906154911.86803-4-philmd@linaro.org>
To improve readability, use the registerfields API.
Define the register bits with FIELD(), and use the
FIELD_EX8() and FIELD_DP8() macros. Remove the
abbreviations in comments.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <20240906154911.86803-3-philmd@linaro.org>
Coding style asks for no space between variable and "++". The next patch
in this series will change one of those assignments. Instead of changing
just one with that patch, change all of them for consistency.
While at it, also fix other coding style problems reported by checkpatch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20240906154911.86803-2-philmd@linaro.org>
Use device_class_set_legacy_reset() instead of opencoding an
assignment to DeviceClass::reset. This change was produced
with:
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/device-reset.cocci \
--keep-comments --smpl-spacing --in-place --dir hw
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-8-peter.maydell@linaro.org
We pass a ResetType argument to the Resettable class enter
phase method, but we don't pass it to hold and exit, even though
the callsites have it readily available. This means that if
a device cared about the ResetType it would need to record it
in the enter phase method to use later on. Pass the type to
all three of the phase methods to avoid having to do that.
Commit created with
for dir in hw target include; do \
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/reset-type.cocci \
--keep-comments --smpl-spacing --in-place \
--include-headers --dir $dir; done
and no manual edits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-5-peter.maydell@linaro.org
The ADM1266 is a cascadable super sequencer with margin control and
fault recording.
This commit adds basic support for its PMBus commands and models
the identification registers that can be modified in a firmware
update.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
[PMD: Cover file in MAINTAINERS]
Message-ID: <20231023-staging-pmbus-v3-v4-5-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
hw.h only contains the protoype of one function nowadays, hw_error(),
so all files that do not use this function anymore also do not need
to include this header anymore.
Message-Id: <20230216142915.304481-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This adds the ISL69259, using all the same functionality as the existing
ISL69260 but overriding the IC_DEVICE_ID.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-4-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds a passthrough for PMBUS_IC_DEVICE_ID to allow Renesas
voltage regulators to return the integrated circuit device ID if they
would like to.
The behavior is very device specific, so it hasn't been added to the
general PMBUS model. Additionally, if the device ID hasn't been set,
then the voltage regulator will respond with the error byte value. The
guest error message will change slightly for IC_DEVICE_ID with this
commit.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-3-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
MAX31785 is a PMBus compliant 6-Channel fan controller. It supports 6 fan
channels, 11 temperature sensors, and 6-Channel ADC to measure the remote
voltages. Datasheet can be found here:
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
This initial version of the driver has skeleton and support for the
fan channels. Requests for temperature sensors, and ADC Channels the
are serviced with the default values as per the datasheet. No additional
instrumentation is done. NV Log feature is not supported.
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-5-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently there is no way for a board model's Kconfig stanza to
say "I have an i2c bus which the user can plug an i2c device into,
build all the free-standing i2c devices". The Kconfig mechanism
for this is the "device group". Add an I2C_DEVICES group along
the same lines as the existing PCI_DEVICES. Simple free-standing
i2c devices which a user might plausibly want to be able to
plug in on the QEMU commandline should have
default y if I2C_DEVICES
and board models which have an i2c bus that is user-accessible
should use
imply I2C_DEVICES
to cause those pluggable devices to be built.
In this commit we mark only a fairly conservative set of i2c devices
as belonging to the I2C_DEVICES group: the simple sensors and RTCs
(not including PMBus devices or devices which need GPIO lines to be
connected).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20220208155911.3408455-2-peter.maydell@linaro.org
This commit adds emulation of the magnetometer on the LSM303DLHC.
It allows the magnetometer's X, Y and Z outputs to be set via the
mag-x, mag-y and mag-z properties, as well as the 12-bit
temperature output via the temperature property. Sensor can be
enabled with 'CONFIG_LSM303DLHC_MAG=y'.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Message-id: 20220130095032.35392-1-kevin.townsend@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This contains some hardcoded register values that were obtained from the
hardware after reading the temperature.
It does enough to test the Linux kernel driver. The FIFO mode, IRQs and
operation modes other than the default as used by Linux are not modelled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210616073358.750472-2-joel@jms.id.au>
[ clg: - Fixed sequential reading
- Reworked regs_reset_state array
- Moved model under hw/sensor/ ]
Message-Id: <20210629142336.750058-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The MAX34451 is a Maxim power-supply system manager that can monitor up to 16 voltage rails or currents. It also contains a temperature sensor and supports up to four external temperature sensors.
This commit adds support for interfacing with it, and setting limits on the supported sensors.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-5-titusr@google.com>
[Moved the device to the sensor directory]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Emmanuel Blot